-40%

PIR Motion Sensor 2in1 streamline steps Stair Wireless Smart Lighting Controller

$ 42.23

Availability: 49 in stock
  • Refund will be given as: Money back or replacement (buyer's choice)
  • Output Voltage: 12V
  • Condition: New
  • Type: Led ladder Controller
  • Lighting Technology: LED
  • All returns accepted: Returns Accepted
  • Restocking Fee: No
  • Brand: Sense Step led Control
  • Return shipping will be paid by: Buyer
  • Item must be returned within: 30 Days

    Description

    Important note:
    The positive and negative terminals of the power supply input of the
    controller cannot be reversed, the red wire V+ is connected to the
    positive electrode of the switching power supply, and the blue (or black
    wire) V- is connected to the negative electrode of the switching power
    supply.
    Product packaging LED Controller set include:
    1 * 36 channel LED Controller
    2 * Motion Sensors (white)
    Note
    : 1-you need buy the Power supply & white strip lights and addressable strip lights
    2-
    The sensor has been changed to white.
    Product description:
    36-channel multi-function LED controller with two sensors, which can
    drive 2 kinds of LED lights, one is a dreamcolor light that supports a
    universal SPI single-wire chip, such as the universal 1903, 1909, 1912,
    TM1812, WS2811, 16703, WS2812B, 8205, 8206 and so on full-color pixel
    LED lights, the control system at the lower left corner of DO1, GND,
    DO2, GND with 2 parallel output terminals, can be connected to the left
    and right sides of the stairs lights. The output terminals on both sides
    of the controller are for the single-color light strips used on the
    36-way stair tread, the number of light strips can be adjusted. The
    function setting of the induction controller is selected by the buttons.
    The setting is displayed through the 4-digit digital tubes on the left.
    Connection guide
    Please connect the controller and motion sensor according to the drawing:
    Setting guide
    you can easy set the controller like above code direction, if you can not get the effect you like , please full read the following guide, thanks.
    The * in the below words instead of number, please know, thanks.
    1.When you power on the controller, it will display **-L, it is the speed of horse racing light, which should be installed on the handrail or wall, you can press SPEED +, or SPEED – to adjust its running speed easily.
    2.If you want to change more effect, press set to choose options, please.
    3.When you press SET, it display L***, it is the pixel of horse, press SPEED+/ SPEED- to adjust. If you use 20IC/m (60LEDs/m) strip light, it can drive about 40m long.
    4.When it display LP**, it is color of horse racing light, press SPEED+/ SPEED- to adjust, there is white- red- green- blue- yellow- purple- cyan, and auto changing available to choose.
    5.When it display LH**, it is speed of horse racing light, press SPEED+ /SPEED- to adjust.
    6.When it display F***, it is the stairs setting, press SPEED+ /SPEED- to adjust, make it same quantity to your stairs.
    7.When it display FP**, it is the stair light lighting up mode, it is only one for now, can not be changed.
    8.When it display FH**, it is stair lighting up speed, press SPEED+ /SPEED- to adjust, the number rise, the speed down.
    9.When it display E***, it is the delay time after all light lighted up, it is not real living time, you can try to adjust it by SPEED+ /SPEED-.
    *Horse racing light pixel(L***) * its running speed(LH**) = Stairs quantity(F***) * Its lighting up speed(FH**)
    press set again to it display **-L, it will auto store the setting you did, when you reboot the system, it will apply the setting.